IMPORTANT PLUMBING INSIGHTS FOR INSTALLING A BATHTUB

Important Plumbing Insights for Installing a Bathtub

Important Plumbing Insights for Installing a Bathtub

Blog Article

Book Service

We have found the article on Installing A Bathtub down the page on the internet and concluded it made perfect sense to discuss it with you over here.


Installing A Bathtub
Setting up a bathtub isn't exactly brain surgery, but it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately difficult task. If the old bathtub is conveniently accessible, the job can move immediately; if you need to open a wall to remove the old tub and also position the brand-new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old bathtub and embeded in the new one. Make sure you have qualified on your own for the work as well as are comfortable attempting it. Instead of working with a service provider to take control of a halfway-completed job, it is much better to take into consideration using one prior to you begin. Opportunities are you might require a professional plumber to make tube links.
This short article will certainly aid you install a new bath tub in your bathroom if you have actually currently bought a brand-new tub and also do not need to alter the setup of your previous water pipes.
Your tools as well as material checklist must comprise the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Preparing for the Installment


    First of all, the sustaining structure supplied with the bath must be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to stop pressure on the tub.
    Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the supplied washers.
    Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its last setting.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any water staying in the system. The process of eliminating the existing taps can be quite troublesome as a result of the restricted access that is usually the instance.
    Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
    Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.

    Installing the Bathtub


    Making use of the two wood boards under its feet, place the bathtub in the needed placement. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
    The next objective is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and readjusting the feet on the bath tub up until the spirit level checks out level.
    To mount taps, fit the bottom of the furthest versatile tap adapter to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
    Activate the supply of water as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if required. Fill up the bathtub as well as likewise inspect the overflow outlet and the normal outlet for leakages.
    Finally, fix the bath paneling as described in the maker's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has actually been utilized at least once as this will certainly settle it into its last position.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the current supply pipes.
    If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in area between the faucet and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The former type needs to be attached to the faucet finishes initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bath tub


    In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack an inflexible seal, creating the water to penetrate the wall surface between the bath as well as the tiling, causing problems with moisture and feasible leakages to the ceiling below.
    You can select from a variety of coloured sealants to assimilate your components and also installations. They are sold in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealer can split rather very early if you do not take into account this movement before securing.
    Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof sticky and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    Do you really like reading up on How to Install a Bathtub? Make a short review further down. We will be delighted to see your reactions about this entry. We hope that you visit us again in the future. Enjoyed our entry? Please share it. Let other people discover it. Thank you for your time. Visit us again soon.


    Secure your plumbing; seek professionals.

    Report this page